Call (855) 671-4316
Water removalWater extractionStructural dryingFlood and sewage cleanup

Sherman Oaks, California · 91403

Water damage restoration in Sherman Oaks, CA

Need water damage restoration in Sherman Oaks? Call and you will be connected with an independent restoration company for emergency water removal, water extraction and structural drying.

Call (855) 671-4316Calls connect to an independent restoration company serving Sherman Oaks.
Drying equipment in a Sherman Oaks area home
24 to 48 hoursEPA drying window[EPA]
If water is coming in right now: shut off the water, stay clear of wet outlets[CDC], photograph the damage[FEMA] and call. Wet materials should be dried within 24 to 48 hours[EPA].

Emergency water removal for Sherman Oaks homes

Water damage restoration in Sherman Oaks begins with water removal. Pumps handle deep water, and extraction units pull water from carpet, pad and tile so the drying equipment can do its job. Water spreads under walls into nearby rooms, so crews check moisture beyond the room where the leak started.

Next is mitigation and structural drying. Materials that cannot be dried in place come out, and air movers and dehumidifiers run until readings show the structure is dry. EPA guidance is to keep indoor humidity under 60 percent[EPA].

How a water damage job runs in Sherman Oaks

  1. Stop the source. Close the main shut-off or the fixture valve.
  2. Document. Photos and video before anything moves[FEMA].
  3. Extract. Standing water out of floors, carpet and pad.
  4. Remove. Wet materials that cannot dry in time come out[EPA flood cleanup guide].
  5. Dry and verify. Equipment runs until moisture readings are normal.

Flood, sewage and pipe damage in Sherman Oaks

Water extraction under way on a wet floor

What to do first when water gets into a home in Sherman Oaks

  • Shut off the source. Use the valve at the fixture first. If water keeps coming, close the main shut-off for the house.
  • Stay safe. Do not walk through water near electrical outlets or appliances; disconnect appliances before power comes back on[CDC].
  • Take pictures. Photograph and video the damage, room by room, before cleanup starts[FEMA].
  • Protect belongings. Move rugs, electronics and paper goods to a dry area, and put furniture legs on blocks.
  • Start drying fast. The EPA says to dry wet materials within 24 to 48 hours[EPA]. Water left longer moves further into floors and walls.

Do not use a household vacuum on standing water, and do not turn on ceiling fans or lights under a wet ceiling.

Signs you need water damage restoration, not just a mop

  • Baseboards or door casings are swelling
  • Vinyl plank or laminate is lifting or cupping
  • Stains are spreading on a ceiling or wall
  • Water reached cabinets, closets or a hallway
  • A drain or toilet backed up
  • A damp smell stays after the floor feels dry

Any of these usually means water has moved into materials you cannot dry with towels and a fan. A moisture meter will show how far it went.

What water damage restoration in Sherman Oaks includes

Water damage restoration is more than pulling up wet carpet. A typical job in Sherman Oaks moves through six stages, and skipping one is how hidden moisture gets left behind.

  • Inspection and moisture mapping. The technician confirms the leak is stopped, then maps how far the water traveled with moisture meters and infrared cameras.
  • Water removal. Submersible pumps take out deep water, and extraction units pull water from carpet, pad and hard floors. Mechanical extraction removes water much faster than air drying can.
  • Removal of what cannot dry. Soaked pad, baseboards, the lower part of wet drywall and wet insulation come out when they cannot be dried in place. The EPA says wet materials that cannot be thoroughly cleaned and dried within 24 to 48 hours should be discarded[EPA flood cleanup guide].
  • Structural drying. Dehumidifiers and air movers run in a closed space, and the goal is relative humidity under 60 percent, ideally 30 to 50 percent[EPA].
  • Cleaning. Surfaces touched by contaminated water are cleaned and disinfected. The CDC says to throw away items that cannot be disinfected, such as wall coverings, cloth, rugs and drywall[CDC].
  • Final readings. Drying is finished when the readings say so, not when the surface feels dry. Ask for the daily log.

Where most household water damage starts

  • Water heaters. Tanks rust through at the bottom, and relief valves and supply connections drip. In many Valley homes the heater sits in a garage or a closet next to finished rooms.
  • Washing machine hoses. Rubber supply hoses crack with age and can release water at full line pressure until someone closes the valve.
  • Toilets and supply lines. A failed fill valve, cracked tank or loose supply line can run for hours, often while nobody is home.
  • Air conditioning condensate. A clogged drain line backs up the drain pan, and the overflow lands in the ceiling below or on the floor around the air handler.
  • Refrigerators and dishwashers. Ice maker lines and dishwasher connections leak slowly under cabinets, where the water can sit for weeks.
  • Winter storms and roof leaks. Heavy rain finds its way in around flashing, vents and windows, and contaminated wind-driven rain counts as Category 3 water[IICRC 2026 position statement].

The source matters because it sets the water category and the starting point for moisture mapping.

Clean water, gray water and sewage: the three categories

Category 1Clean source: a supply line, faucet or water heater.
Category 2Significant contamination: for example, washer or dishwasher discharge.
Category 3Grossly contaminated: sewage, rising rivers or streams.

The IICRC splits water into three categories. Its examples of grossly contaminated Category 3 water include sewage, waste line backflows from beyond a trap, seawater flooding, rising rivers or streams and contaminated wind-driven rain[IICRC 2026 position statement].

It also changes how the crew works. With Category 2 or 3 water, removal and cleaning happen first, under contamination controls, and drying comes after; Category 1 can go straight to drying[IICRC 2026 position statement].

Time matters too. The IICRC notes that time and temperature can change the category[IICRC 2026 position statement], so a clean leak left sitting for days can be treated as contaminated water.

Hidden water: the spots crews check first

On a concrete slab, water does not drain away. It spreads sideways under baseboards, cabinets and flooring into the next room, which is why the wet area on the meter is often larger than the wet area you can see.

Air conditioning is a frequent source. The EPA advises keeping AC drip pans clean and drain lines flowing[EPA], and notes that pans which do not drain can let water into the system[EPA]. When the air handler sits in the attic, an overflowing pan usually shows up first as a ceiling stain.

Places to check:

  • Inside walls around leaking or sweating pipes[EPA]
  • Under vinyl plank, laminate and carpet pad
  • Behind the refrigerator ice maker line and dishwasher
  • Under the water heater and washing machine
  • Roof materials above ceilings after a roof leak[EPA]

LADWP’s leak tips include a simple toilet test: put food coloring in the tank, and if color shows up in the bowl without flushing, there is a leak that should be fixed[LADWP].

Water damage room by room

  • Kitchens. Dishwasher, sink and ice maker leaks run under the cabinets. Toe kicks often come off so air can reach the floor underneath, and cabinet backs are checked with a meter.
  • Bathrooms. Toilet overflows, tub drains and shower valves wet the subfloor and the wall behind the fixture. A toilet overflow from the bowl is treated by its source, and a backup through the drain is Category 3[IICRC 2026 position statement].
  • Laundry rooms. Burst washer hoses release a lot of water fast, and it usually reaches the next room under the wall. Drain backups bring gray water.
  • Garages and water heater closets. A leaking tank spreads across the garage slab and under the wall into the house. Stored boxes on the floor soak up water and should be moved first.
  • Bedrooms and living areas. Carpet and pad hold a lot of water. Extraction comes first, then the pad is checked; soaked pad is usually replaced rather than dried.
  • Ceilings. Roof leaks and AC overflows wet insulation and drywall above. Wet ceilings can sag, so the area under them is kept clear.

Slab floors and raised floors

Los Angeles City Planning’s history of postwar tract housing notes that these houses often have concrete slab floors rather than raised floors with wood joists[LA City Planning]. Much of the Valley was built in that era, so on many calls the water is on or under a slab.

Raised foundations show up more in older homes. Earthquake Brace + Bolt, the state program for retrofitting raised-foundation houses, uses the percentage of pre-1940 houses in a ZIP code as one of its selection criteria[Earthquake Brace + Bolt]. Water under a raised floor can sit unseen until the floor softens.

Either way, the drying plan changes: slab jobs focus on flooring, baseboards and the bottom of walls, while raised-floor jobs add the subfloor, joists and crawl space.

Water removal and drying equipment used in Sherman Oaks

  • Pumps and extractors. Submersible pumps remove deep water. Extraction wands and weighted tools pull water out of carpet and pad.
  • Air movers. Fans set at angles along walls and floors move air across wet materials.
  • Dehumidifiers. Remove water from the air. Without them, air movers just push damp air around the room.
  • Moisture meters. Measure the water in drywall, framing and subfloor, and confirm when each area is dry.
  • Infrared cameras. Help locate wet areas behind finished surfaces, with meters used to confirm.
  • Containment. Plastic sheeting closes off the work area, which keeps contaminated water and drying air where they belong.

How long drying takes in Sherman Oaks

Small leaks found early dry in days; whole-house floods take longer, and the EPA says the drying-out process after a flood could take several weeks[EPA flood cleanup guide]. Either way, the work should start within 24 to 48 hours[EPA].

Dry outdoor air is not the same as a dry wall. EPA guidance is to ventilate when outside air is cold and dry and to dehumidify when it is warm and humid[EPA], and the inside of a wet wall cavity or carpet pad still needs moving air and dehumidification to dry in time.

Keep the equipment on and in place. Each time it is turned off, the air in the room gets damp again and drying slows down.

Saving belongings and materials after water damage

Two questions decide it: was the water clean, and how fast can the item dry? Wet materials that cannot be cleaned and dried within 24 to 48 hours should be thrown out, according to the EPA[EPA flood cleanup guide]. With floodwater, the CDC says to throw away items that cannot be disinfected, like wall coverings, cloth, rugs and drywall[CDC].

With clean water caught early, the EPA notes that wallboard, fiberglass insulation and wall-to-wall carpet may sometimes be dried and saved, though replacing them can avoid indoor air problems later[EPA flood cleanup guide].

Photograph everything before it goes to the curb[FEMA], and keep a list of what was removed.

Earthquake water damage in the Valley

The magnitude 6.7 Northridge earthquake struck at 4:30 in the morning on January 17, 1994, on a buried thrust fault rooted under the San Fernando Valley[USGS]. It left more than 7,000 people injured and 20,000 residents homeless, with property damage estimated at about 40 billion dollars[USGS].

Shaking strong enough to topple water heaters and break water mains is one of the effects the USGS lists[USGS]. State law requires every residential water heater to be braced, anchored or strapped[California Health and Safety Code 19211], and the state’s bracing guidelines recommend flexible water and gas connectors along with at least two straps[California DSA].

Gas water heater with two earthquake straps and a small puddle on the garage floor

After an earthquake, check the water heater, the lines under sinks and the main shut-off before anything else. If water is running, close the main and keep out of rooms where water has reached outlets[CDC].

Winter storms and roof leaks

Rain here tends to arrive in bursts. The National Weather Service’s February 2024 climate report for downtown Los Angeles shows 4.10 inches on February 4, 2.93 inches on February 5 and 12.66 inches for the month[NWS Los Angeles].

Storms like that find every weak spot: roof flashing, skylights, sliding door tracks and low garage slabs. Water that comes through the roof soaks insulation and drywall in the ceiling before it shows as a stain.

Do not stand under a sagging ceiling, and turn off power to rooms where water is near outlets or fixtures if you can do so safely[CDC].

When a drain backs up into the house

A backup from a toilet, tub or floor drain is grossly contaminated water under the IICRC categories[IICRC 2026 position statement]. The area is closed off, contaminated porous materials come out, and surfaces are cleaned before any drying starts.

In the City of Los Angeles, the public sewer main belongs to the city, but the property owner is responsible for the entire sewer lateral, from the building to the street connection. LA Sanitation also says that if any fixture in a home sits lower than the street manhole cover, the property needs a backwater valve, which requires a permit from the Department of Building and Safety[LA Sanitation].

Before you go back into a flooded home

Turn around at flooded roads. Six inches of fast-moving water can knock an adult down, and 12 inches of rushing water can sweep away most cars, according to the NWS[NWS].

If there is standing water inside, be ready to turn off the power, and unplug appliances so they do not shock anyone when power returns[CDC]. Take photos and video of every room before cleanup starts[FEMA].

Apartments, condos and townhomes

61% of housing units in ZIP code 91403 are in buildings with two or more units, and 15% are in buildings with 20 or more[U.S. Census Bureau]. In shared buildings, water moves through ceilings and shared walls, so one leak can reach several homes.

If water is coming from the unit above or next door, tell the building manager or HOA right away and photograph where it is entering[FEMA]. Moisture readings should cover the shared walls and the ceiling, not just the floor of your unit.

Talking to the restoration company

  • Which IICRC category does this water fall into?
  • Can you show me the moisture readings and the wet area on a sketch?
  • Which materials are coming out, and which can be dried in place?
  • When will you take readings, and when do you expect the job to be dry?
  • Do I need a plumber to stop the source first?
  • Will you put the scope of work in writing before you start?

Clear answers to these questions are a good sign. So is a technician who takes readings before quoting.

Once the house is dry

Ask for a copy of the final readings and keep them with your damage photos. In the weeks after, watch for a damp smell, new stains or swelling floors. Fix the source for good; the EPA is clear that the water problem must be fixed or it comes back[EPA].

About Sherman Oaks: homes, water and storms

13,045
housing units
1971
median year built
67%
built before 1980
45%
owner-occupied

The Census Bureau counts 13,045 housing units in ZIP code 91403. 36% are detached single-family houses, 61% are in buildings with two or more units, and 45% of occupied homes are owner-occupied[U.S. Census Bureau]. 67% of homes in ZIP code 91403 were built before 1980 and the median year built is 1971[U.S. Census Bureau]. At that age, original galvanized or copper supply lines, cast-iron drains and older shut-off valves deserve a look.

Next to the Sepulveda Basin

The Sepulveda Dam Basin is bordered on the south by the Ventura Freeway and on the east by the San Diego Freeway[USACE]. The Corps operates the dam to store storm runoff and release it into the Los Angeles River without exceeding the channel’s capacity, and says the dam has never spilled[USACE].

Most water damage in Sherman Oaks homes starts inside: supply lines, water heaters, toilets and roof leaks during winter storms. In apartment and condo buildings, a leak in one unit can move through ceilings and shared walls into the next, so moisture readings should cover more than one room.

Water and sewer contacts

Sherman Oaks is part of the City of Los Angeles, so water comes from LADWP. Leaks at the street, the meter or a broken main are reported to LADWP at 1-800-DIAL-DWP (1-800-342-5397), where representatives answer outage and water trouble calls around the clock[LADWP].

Sewers in the City of Los Angeles are run by LA Sanitation, which lists a customer care line at 1 (800) 773-2489. The city owns the public sewer main, but property owners are responsible for their entire private sewer lateral, from the house to the connection in the street[LA Sanitation].

ZIP codes

This page covers Sherman Oaks, CA 91403.

Nearby communities

Questions about water damage in Sherman Oaks

How quickly does a Sherman Oaks home need to dry?

The EPA advises drying wet areas and items within 24 to 48 hours[EPA].

Who handles a leak at the street or water meter in Sherman Oaks?

A leak on the utility side of the meter belongs to the water provider. Sherman Oaks is part of the City of Los Angeles, so water comes from LADWP. Leaks at the street, the meter or a broken main are reported to LADWP at 1-800-DIAL-DWP (1-800-342-5397), where representatives answer outage and water trouble calls around the clock[LADWP].

How long does water damage restoration take in Sherman Oaks?

A small clean-water leak caught early can often be dried in a few days. After a flood, the EPA says drying out can take several weeks[EPA flood cleanup guide].

Will the crew remove drywall?

Only what cannot be dried. Drywall soaked by floodwater or sewage generally comes out; the CDC lists drywall among items to throw away when it cannot be disinfected[CDC].

Does my water heater have to be strapped?

Yes. California law requires residential water heaters to be braced, anchored or strapped to resist falling or moving in an earthquake[California Health and Safety Code 19211].

Should I open the windows to help it dry?

It depends on the weather. EPA guidance is to ventilate when outside air is cold and dry and to dehumidify when it is warm and humid[EPA].

Who is responsible for a sewer backup from the lateral?

In the City of Los Angeles, property owners are responsible for the entire private sewer lateral, from the building to the street connection[LA Sanitation].

Is this a restoration company?

No. 818 Damage is a referral service. Your call connects you with an independent restoration company that serves Sherman Oaks.

Water in your Sherman Oaks home?

One call connects you with an independent restoration company for water removal and drying.

Call (855) 671-4316
Call (855) 671-4316